Most dishwashers are outfitted with a system to clear minor mechanical malfunctions. So that means if dishwasher owners are working with any dishwasher model, there are bound to be ways to reset it. Beko, one of the largest appliance manufacturers in Turkey and very popular in the United Kingdom, has dishwashers with these systems put in place.
Before you go and spend your hard-earned money on a specialist in dishwasher repairs, you want to make sure you’ve done everything you possibly can on your end. So we’re going to go through and give you a few quick answers on how to reset your Beko dishwasher.
Can You Reset a Beko Dishwasher?
The short answer to this question is yes. Before you push any buttons, though, you want to make sure that you check that the door latch of the dishwasher unit is actually clicking into place. If your dishwasher has stopped running, this could be the simple answer as the system will not allow a cleaning cycle to happen when the door is ajar.
So before you do anything, you want to open the dishwasher door completely and then close it firmly. When you do this, make sure to pay attention to see if you hear the door latch click into place. If this is the case, then you’ll want to look at replacing that door latch.
If the latch is engaged, then you’re going to want to walk through the system that the company has put in place to help reset the system. On the control panel, you will see a start/stop button. Start by holding this button down for three seconds which will cancel the dishwasher cycle the unit is currently running. After the cycle has stopped, you will want to push that button again, this time for seven seconds. This will reset the dishwasher from any minor issues.
What causes a blocked dishwasher?
There are many reasons that you may be dealing with dishwasher blockage. One of the biggest dishwasher clogging issues may be a clogged dishwasher filter basket. This happens when the drain basket needs to be cleaned of food debris. This can also be caused by mineral deposit buildup from hard water.
Dishwasher clogs can also be caused due to the drain hose. This is the hose that connects your kitchen sink to the garbage disposal, and sometimes it will get backed up. Doing a deep clean of the dishwasher drain pipe will remove any gunk left by dirty water and fix any drainage issues.
Speaking of garbage disposals, this too can be the cause of dishwasher draining issues if the installation wasn’t completed properly. When a new installation goes in, often a knockout plug is placed. If this isn’t removed, then that can be quite the problem. Also, if you are dealing with older disposal, you may find that the things you put in there, like chunks of food, might be causing a bit of a backup because these two appliances use the same drain pipe.
The dishwasher drain pipe could be clogged, and that may be the issue of why your dishwasher is not working properly. The easiest way to tell if this is happening is if, when using the dishwasher, water is coming back up through your sink drain.
The last issue might have to do with your sewer line. If, after eliminating the other options, this becomes the clear reason why you’re dealing with a clogged or blocked dishwasher line, then you’ll need to reach out to a professional to get the entire sewer system assessed.
How do I know my dishwasher is blocked?
There are a lot of signs that you can watch for if you feel that your dishwasher is not working properly and delivering clean dishes.
If you start hearing abnormal sounds like gurgling or the unit starts shaking as the dishwasher is going through its cycles, then there may be a clog in one of the lines.
Does the water back up into your sink when you run your dishwasher? If this happens, you might want to run your garbage disposal to see if it is simply a mass of food particles stuck there that is causing the backlog.
If you notice that the unit is draining slower than normal, it could be a problem with your dishwasher drain pump. You can see this by excess water being present in the bottom of the dishwasher when you open it.
Excess water in the bottom of the dishwasher can also be due to leftover food blocking the drainage system from doing its job. If this is the case, you’ll want to remove the drain basket and clean it thoroughly of any bits of food or debris that may be there.
How to avoid dishwasher blockages?
Because your dishwasher uses the same plumbing as your sink, you want to make sure that none of that debris goes down into the dishwasher. This means cleaning after dishes thoroughly with soapy water before placing them in the dishwasher rack.
You should also clean your dishwasher thoroughly on a regular basis. You can do this using white vinegar and warm water with a flexible brush or other alternative cleaning methods. Every month, you should run a few full cycles with hot water, which will help clean every inch of the dishwasher and alleviate the chance of clogs.
Blockages can cause water flooding, which is not anything someone would want to deal with in their kitchen. So the best way to ensure to avoid blockages is to do a thorough cleaning and maintenance of your dishwasher at all times. This might even include cleaning the dishwasher air cap or checking on the water supply lines to ensure there is no leaking.
So there you have it. Not only can you reset your Beko dishwasher, but there are plenty of ways to prevent issues that will cause the need for resetting that appliance. Hopefully, this information has helped you with your issues.
Founder of homeappliancegeek.com, avid cook, and lover of Asian food.
Signature dishes include Thai Red Curry, Chicken Saag, Bibimbap and Sushi.
Massive clean freak; a habit baked-in after spending 9 years in the catering industry.
The one appliance he couldn’t live without? Easily the dishwasher (total relationship saver!).